#Plastic lattice fencing how to
#Plastic lattice fencing install

If you don’t have a railing on your deck, you can build a privacy fence along the deck in the desired area. If you already have a rail on your deck, you can add a privacy screen to the top of the railing. Our next installation example is for adding Privacy to your deck. The lattice sheets are supported by the frame sections that are attached to the deck post. This type of installation does not need u-channel. The picture above shows the lattice framed and installed on the front side of the post. You will also need to secure the lattice sheet on the front of the post. Screw or nail through the channel to attach it to the deck boards. The channel also offers a capped look to the lattice sheet.

The u-channel will help guide the lattice along the deck boards. The picture above shows the lattice on the front of the post with the use of the u-channel along the top of the lattice sheet. Don’t be overwhelmed with all the options. No need to predrill oversized holes for our lattice. You can either screw or nail through the lattice sheet to a support.

#Plastic lattice fencing install

You can put the lattice on the front of the support post, you can frame the lattice sheet and install on the front of the support post, use a u-channel or install the lattice without a u-channel. Ok, now on to the first installation example.ĭeck skirting has 4 common ways you can install the lattice. This will prevent the blade from chopping through the lattice sheet. Two when cutting our lattice with a circular saw, reverse the blade. This will prevent rust stains on your lattice. One use stainless steel nails or screws to secure your lattice sheets. If you have questions, please call us! Since Permalatt’s lattice can be used for so many projects there can be more than one way for installation.īefore we get into each project type we have a couple of suggestions. Please remember, you have options for your lattice installation. We’re going to share a few of our installation suggestions as well as ways our customers have installed our lattice in their projects.

#Plastic lattice fencing how to

It seems the next topic is how to cut lattice. They are made to be used as fences, however, other popular uses for them are as deck skirts, patio enclosures, climbing flower wall, pool enclosures, window screen, gazebos wall, and pet enclosures.When you Google lattice installation you may notice the first topic is lattice skirting. Most vinyl lattice panels come pre-made in 4 x 8 feet rectangular panels. If your ground pitch is 4 inches, the next post should be 4 inches shallower into the ground and the next panel should be secured at a height 4 inches less taller than the previous panel. The difference between them is your ground pitch. Take the sticks out and measure from the bottom of the stick to the string. Then tie a string around both sticks close to the ground. In order to figure out if the land is on an incline, ground in two sticks in front of two adjacent posts. A 90 degree post should be aligned with the direction of the string.

Tie a weight on a string and let it drop alongside a post.

Check to see if there is an incline so that you can order taller posts for hilly area fence installation. Use a string pulled taut against the fences to make sure that all posts are in alignment. Measure each time a new post is put in, using the previous post to check measurements against. Instead of finding out towards the end of installation that a hole is too deep, too shallow, or a post is out of line, always double check your work as you go. The more watery the cement mixture, the more harder it will be to keep the fence level while it is curing. For best results, pre-mix the cement in a wheelbarrow instead of pouring in powder and water separately into the hole in the ground. Use as little water as possible in mixing cement. This method is more slow-going at first, but will require less repair time later. Instead, install the first post by digging the hole and cementing the post, and use the upright post to begin measuring for the location of the second post. Contrary to popular fence installation manuals, digging holes, cementing the posts, then finding out that the spacing is off when trying to install the framework is a costly no-no.